Telescope Eyepieces
SBony Red Line vs Gold Line Eyepieces: Fixing the Barlow Wobble for Good
The SBony red line eyepieces wobble in barlow lenses with a compression ring, but a simple 3D printed washer fixes it. Here is what we found and which line to pick.
Introduction
SBony offers two lines of budget-friendly eyepieces: the gold line and the red line. On paper, the choice between them looks like pure personal preference. But there is one practical issue worth knowing about before you buy, and it affects the red line specifically when used with certain barlow lenses.
This follow-up focuses on the red line wobble problem, how to fix it cheaply, and how the two lines compare once the fix is in place.
The Problem: Red Line Eyepieces Slip in Compression Ring Barlows
When a red line eyepiece is inserted into a barlow lens with a compression ring (sometimes called a copper ring) and tightened down, it can still wobble and even pop out. This was tested with a Celestron Omni 2X barlow, and every red line eyepiece showed the problem to some degree. The gold line eyepieces, by contrast, sat rock solid in the same barlow.
Other observers have reported the same issue when using red line eyepieces in a binoviewer, so this is not limited to a single accessory.

Importantly, the problem only appears with compression ring holders. In a barlow that uses a simple tightening screw, the red line eyepieces hold just fine. And it is not a universal flaw of narrow-barrel eyepieces either: other brands with similar skinny regions on their barrels, such as a Meoptics eyepiece tested for comparison, seated tightly without any wobble.
What Causes the Wobble
Unscrewing the barrel bases from both eyepiece types reveals the difference. The upper lip of the red line barrel is slightly thinner than the equivalent section on the gold line. The measured difference is about 0.020 inches.
Because the compression ring cannot clamp down far enough, the eyepiece stays loose in the holder. The fix, in principle, is simple: add roughly 0.020 inches of spacer material so the ring can grip properly.

Quick DIY Fixes: Milk Jug Spacers and Teflon Tape
The first attempt used the classic amateur astronomer trick: cutting a thin washer from the flat plastic of a washed milk jug. The polyethylene is about 0.016 inches thick, which sounds promising. In practice, the washer needs to be extremely small and precise, narrower than the barrel itself, and hand-cutting it proved too crude to work.
Method two borrowed from plumbing: teflon tape, twisted into a thin rope and wrapped around the barrel above the threads. Surprisingly, this worked. The eyepiece became very tight in the barlow. But the wrap looked messy, started to shred, and small bits of teflon could end up loose inside the barlow, which is exactly what you do not want.

So the household fixes either failed outright or worked poorly. The goal became making washers with exact dimensions: about 0.020 of an inch thick, no wider than the 1.25-inch barrel, but wider than the threads.
The Winning Fix: 3D Printed Spacer Washers
A 3D printer turned out to be the ideal solution. The washers are simple shapes, and a set of five was printed: three identical ones for the eyepieces that share the same barrel design, and two slightly different ones for the 20 mm eyepiece, which has a different thread arrangement and needs a super-skinny washer that fits around its threads.
The final file includes four washers and is available on Thingiverse for anyone who wants to print their own set.

The final test results were excellent. The 6 mm, 9 mm, and 15 mm eyepieces all seated solidly in the compression ring barlow with the printed washers in place, each described as solid as a rock. The 20 mm was slightly trickier because the tiny washer has to seat down onto the lip around the threads, but once fitted, it held firmly too.
One printing note: use the highest resolution your printer allows. The tolerances are tight and the parts are small, but even at high resolution each washer takes only about four or five minutes to print.
Which One Should You Buy?
Once the printed spacers are fitted to the red line eyepieces, the practical difference between the two lines largely disappears. It genuinely comes down to preference:
- Choose the red line if you like the rubber grips and the narrow band styling.
- Choose the gold line if you do not care about rubber grips and prefer the tapered barrel.
There is only about a $10 difference between them, so neither choice carries a meaningful price penalty.
Conclusion
The red line SBony eyepieces have a real fitment quirk in barlows and binoviewers with compression rings, caused by a slightly thinner barrel lip. Milk jug spacers fail and teflon tape is messy, but a small set of 3D printed washers solves the problem completely and takes minutes to produce. With that fix in place, pick whichever line suits your grip and styling preference and enjoy the views.
Product link
View more details for SBony Red Line Eyepieces
This product is mentioned in the review. Check the specifications, options, and compatibility before buying.
View more details for SBony Red Line Eyepieces