Snowboard Bindings
Bent Metal Solution Bindings Review: A Stiff Binding Built for Charging
A very stiff, responsive freeride binding with adjustable drive plates, on-the-fly forward lean, and a few fit quirks to know before buying.
Introduction
The Bent Metal Solution is a binding aimed squarely at riders who want to charge hard. Tested on a spring day at Copper Mountain with soft, creamy groomers up top turning to slush and chop lower down, it proved to be a very stiff, very responsive binding with plenty of power underfoot. It was ridden with a Ride Shadowband snowboard and K2 Thraxis boots, in a large size.
This is not a binding for everyone. It is stiff, it demands a boot that fits it well, and it sits at the aggressive end of the freeride spectrum. But for the right rider, it delivers a lot.
Adjustability: Fit It to Your Boot
The Solution offers a lot of ways to dial in fit. The heel cup adjusts in and out to center your boot, and moving it also changes the placement of the highback, so you can rotate that to suit your stance. There are three distinct positions for the heel strap depending on where the heel cup sits.
The straps themselves use twist tabs: flip them up, unscrew, and you can lengthen or shorten the strap to change how it sits over your instep or on the boot.

One caveat came up in testing: the molded straps have no excess padding, which keeps the connection direct, but the outer edge is a bit bulkier. That created a pinch point over the instep when the straps were cranked down, with some pressure felt on the inside of the boot from the twist cam and on the outside when over-tightening the toe strap. A slightly larger cutout would fit more boot shapes comfortably.
Highback and Drive Plates
The highback is adjustable for forward lean via a twist block, and you can change it on the fly. It is very supportive and responsive, with a slight wing that cradles without much give, letting you push into it for better power transmission.

The drive plates are another standout feature: they can be swapped out. The Solution comes with the stiffest plate in the range, so your only option is to go progressively softer with other models. That makes the stock setup the most aggressive choice, but the ability to swap gives you a path to tune the feel.
Ride Feel: Stiff, Powerful, Responsive
These are stiff bindings, and you feel it the moment you drive into them. There is a ton of power, and even with the mini disc underfoot there is very little play, just response you can feel through toe and heel edges and from side to side.

The straps have slightly more flex than others in this stiffness category, but they still hold you in firmly and stayed locked in all day with no worries. The moderately damp feel means you will notice some chatter underfoot, which is expected with this much carbon, but the drive plates do a good job of minimizing smaller vibrations so they do not fatigue you as the day goes on. Even in rutted-out terrain, the binding did not cause leg fatigue. In short: this is a binding for going out and charging with.
Things to Consider Before Buying
Sizing matters here. In a large, the heel cup had to be pushed all the way in to work with a size 10 boot, and it pinched the heel enough to cause some boot wear. A medium would have been the better fit for that setup, so riders on the cusp between sizes should think carefully about which way to go.

There are a few smaller quirks too. The toe strap lacks a one-finger quick release, so you have to grab it from the front, while the heel strap has one. There is also a slight buckle rattle with some play in the straps. Neither was a deal breaker, but both are worth noticing.
Buying Advice
This binding suits the full-on freeride rider who wants a stiff, supportive, powerful connection to the board. If you spend your days charging big lines and firm groomers, it makes a lot of sense. If your riding is more playful or park-oriented, this is probably too much binding. Comparable options to look at include the Jones Apollo, the Union Atlas Pro, and the Ride A-10. Bent Metal tends to get overlooked among the bigger names in the market, which makes the Solution an interesting pick for riders willing to look past the usual suspects.
Conclusion
The Bent Metal Solution is a very stiff, very responsive binding with excellent adjustability, swappable drive plates, and a power-forward ride feel that freeride riders will appreciate. Its stiff flex and fit quirks mean it is not for everyone, but for aggressive riders it is a strong, confident choice.
Product link
View more details for Bent Metal Solution
This product is mentioned in the review. Check the specifications, options, and compatibility before buying.
View more details for Bent Metal Solution