Metamorphic Pocket Grip Review: A Five-in-One Clamping Tool for EDC

Introduction

Some tools get forgotten, and some get revived. The Metamorphic Pocket Grip belongs firmly in the second camp. Built by Metamorphic Metal in Motion, it takes a historic tool design loosely based on the Stanley Triplet Wrench, a patent applied for in 1913, and reimagines it with modern materials and machining. The result is what the maker calls a five-in-one clamping machine: pliers, a parallel wrench, a clamp, a bit and hex driver, and a tap holder, all in one pocketable aluminum body with stainless steel jaws.

For anyone drawn to EDC and pocket-carry tools that do real work rather than just look clever, this is a genuinely interesting proposition.

What the Pocket Grip Is

The Pocket Grip is a screw-adjusted clamping tool. A coarse thread on the adjustment ring means it takes only a few spins to move from maximum opening to minimum, which matters more than you might expect when you are reaching for it one-handed. Two versions exist on Kickstarter, and the one covered here is the aluminum version with stainless steel jaws.

The overall shape is more angular and muscular than the 1913 original, and it is about an inch and a half shorter, which makes it noticeably more pocket friendly. If you want the tool to sit discreetly, adjusting the ring changes how far it protrudes.

The Adaptive Parallel Jaw

The headliner feature is the adaptive jaw at one end. Closed fully, the jaws sit parallel, which is why it is described as a parallel wrench. Standard adjustable wrenches maintain parallel jaws but cannot do what this tool can: loosen the grip slightly, rotate the jaw onto the fastener corners at an angle, then cinch down again. That slide, grab, rotate, and finish motion is the reason people often reach for a plier wrench instead of an adjustable wrench, and the Pocket Grip reproduces it here.

When set to full parallel and driven square, the screw mechanism holds with real authority. It does not loosen easily at a full 90-degree engagement, which is exactly what you want from a wrench that doubles as a clamping machine.

Pliers and Vise Functions

Further along the body, a set of jaws behaves much like regular pliers. The jaws are shaped so they do not fully close and do not intersect; instead the points stay aligned over each other. That alignment keeps grip steady on material and leaves smaller recessed areas for holding small items. Dropping a bolt head into the slots in the jaws locks it in place, an approach that recalls the way the Knipex Cobra traps a fastener inside its jaw geometry.

The same end also works as a small vise. A stack of washers slid between parallel jaws and cinched down holds very snugly, which says a lot about how strong the screw mechanism is under compression.

Bit Driver and Tap Holder

In the center of the body there is a bit driver. Loosen the mechanism slightly, drop a bit in, cinch it down, and it sits rock solid. Because the effort is applied at one end and the fulcrum at the other, with the load in the middle, the leverage profile is strong, the same principle that makes a nutcracker effective.

The maker also positions this center opening as a tap holder. A quarter-20 tap, for example, sits centered and held firmly, so it should drive straighter than it would hanging far out on the end of a tool. The plier jaws at the other end can serve as a secondary hex driver if needed, though that is more of a fallback than the intended use; the design is really meant for bolts, and very large bolts will max out the jaw capacity.

Pocketability and Everyday Carry Appeal

For the EDC crowd, the appeal is coverage: pliers, a parallel wrench, a clamp, hex driving in two spots, and tap driving in one compact body. Maintenance is straightforward, with a 5 mm hex used if you want to adjust the mechanism more snugly or take it apart for cleaning.

Carried in a pocket, the threaded adjustment lets you control the profile so nothing sticks out further than you like. It is a handy tool for a lot of different situations, and it earns its place by being genuinely useful rather than merely novel.

Things to Consider Before Buying

The Pocket Grip is a specialist kind of generalist. It will not replace a full toolbox, and jaw capacity on large fasteners is limited. It also launches through a crowdfunding campaign, so availability and delivery timelines are worth checking before ordering. If your daily carry already includes dedicated pliers and a wrench, think about whether one combined tool actually simplifies your kit.

Buying Advice

This tool makes the most sense for people who genuinely value multi-function carry: makers, tinkerers, and anyone who routinely grabs bolts, bits, or small material and wants one rugged piece of metal that can hold all of it. If you appreciate the story of revived tool designs as much as the function, the Pocket Grip offers both.

Conclusion

Metamorphic Metal in Motion has taken a century-old wrench concept and rebuilt it with modern materials while keeping the mechanical logic that made the original clever. The Pocket Grip is a well-thought-out five-in-one clamping tool that rewards people who carry tools to use them. If that describes you, it deserves a close look.