DeWalt FlexTorque DWALFT Review: A Lighted Right-Angle Attachment With Real Flexibility

Introduction

DeWalt has been busy in the right-angle attachment space, and the FlexTorque DWALFT is its latest entry: a lighted, modular right-angle attachment for impact drivers. If you have ever needed to drive a fastener where a regular driver simply cannot fit, this kind of tool earns its place in the bag quickly. After spending time with it, this may well become the general go-to in a crowded category.

What the DeWalt FlexTorque DWALFT Is

The full name is a mouthful: the DeWalt FlexTorque lighted modular right-angle attachment for impact drivers, also known as the DWALFT. It takes a quarter-inch hex bit and turns it 90 degrees, letting you reach fasteners in tight, awkward spaces. The head is magnetically held rather than using a quick-lock collet, and if a short bit gets stuck, a pair of small pliers pops it out easily. One-inch bits work fine in there too.

The front-end attachment alone sells for around $29 to $30 on Amazon at the time of writing, where it has been on sale.

The Built-In Light: Better Than Most

The standout feature is the built-in LED, which recharges over USB-C via a simple flip-open port. Functionally it is as basic as it gets: on or off, and that is about it. But the placement matters more than the feature list. Plenty of LED lights on attachments look great on a store shelf and then miss the mark in use, firing too close, too far, or off-center.

Here, the beam lines up well. With a standard-length bit, the work area sits comfortably within the light envelope, right through the center at a 90-degree angle. Very short bits leave the workpiece down near the edge of the light pool, and longer drill-bit-sized bits can creep past the sweet spot, but for typical impact driving it is genuinely usable.

One quirk: the light shuts off automatically after a period of inactivity, which is reasonable but worth knowing if you leave it switched on. As a bonus, it doubles as a small utility light in the tool bag, performing roughly like a phone flashlight.

Modular Design and Handling

This is where the DWALFT gets interesting. It is part of DeWalt’s modular attachment system. You can run it bare for the shortest footprint, snap on the included ambidextrous handle for more control and precision, or attach a long extension shaft when you need reach. The handle and the extension cannot be used at the same time, but each configuration has a clear purpose.

The compact body gets the head into a nicely usable short space, and in most jobs it is the 90-degree reach that matters rather than the access angle of the input. Compared with DeWalt’s earlier low-profile attempt, which was long and awkward, and the simple fixed designs everyone was making a few years ago, this modular approach feels like the most practical evolution of the concept.

Do You Actually Need an Impact Driver?

DeWalt specifies this attachment for impact drivers only, presumably to avoid high-speed drill use. It features forged gears for added durability, though what that means in practice is not fully spelled out. That said, the tool finds function beyond impact driving. With a bit seated in the head, you can run it by hand with a ratcheting driver, or even just spin the input directly. For light hand-driven fastening in tight spots, it works well even without any power tool attached.

Things to Consider Before Buying

There are a few trade-offs worth weighing. The magnetic bit retention means no quick-lock mechanism, so shorter bits can be fiddly to remove without pliers. The light requires yet another rechargeable device in your kit, and if you already own several right-angle attachments, this one will not be your last temptation. The modular system is genuinely useful, but it also invites you to keep collecting pieces until the tool bag is full of them.

Buying Advice

If you regularly work in tight spaces where a straight driver cannot reach, the DWALFT makes a strong case. The combination of a compact 90-degree head, a light that actually lands where the bit does, and modular extensions for reach or control covers most scenarios you will encounter. At around $29 to $30 for the front-end piece, it is an affordable way to add right-angle capability, and it runs on about any impact driver you already own. If you mind carrying one more USB-C rechargeable gadget, that is the main hesitation, but for most users the convenience outweighs it.

Conclusion

The DeWalt FlexTorque DWALFT is a simple idea executed thoughtfully: a right-angle attachment that gets into short spaces, lights the work area properly, and grows with your needs through a modular system. Turn on the light and go to work.